Skip to main content

Openstack havanna neutron agent-list alive status error

In some scenarios, the openstack neutron-agent status will show as xxx even though you could see he neutron agents services are up and running in the network and compute nodes. Also you could see a fluctuation in the agent status if you try the agent-list command repeatedly.  Confusing, right?

Actually  the problem is not in the actual agent status, but with two default configurations in neutron.conf ie agent_down_time and report_interval. It is the interval during which neutron will check the agent status. There is a bug reported against this issue

https://bugs.launchpad.net/neutron/+bug/1293083

As per the details in the bug " report_interval" is how often an agent sends out a heartbeat to the service. The Neutron service responds to these 'report_state' RPC messages by updating the agent's heartbeat DB record. The last heartbeat is then compared to the configured agent_down_time to determine if the agent is up or down"

The neutron agent-list command uses the agent_down_time value to display the status. The default values are set very low, because of which the alive status is shown as down/fluctuating.

Solution: As suggested in the solution for the bug, update the values of agent_down_time and report_interval to 75 and 30 seconds respectively. Since the above mentioned rpc issue with open-vswitch agent in compute is  resolved by this, all the agents will be shown as alive

Comments

Popular posts from this blog

Windows server 2012: where is my start button??

If you have been using Windows Server OS for a while, the one thing that will strike you most when you login to a Windows server 2012 is that there is no start button!!.. What??..How am I going to manage it?? Microsoft feels that you really dont need a start button, since you can do almost everything from your server  manager or even remotely from your desktop. After all the initial configurations are done, you could also do away with the GUI and go back to server core option.(In server 2012, there is an option to add and remove GUI). So does that mean, you need to learn to live without a start button. Actually no, the start button is very much there .Lets start looking for it. Option 1: There is "charms" bar on the side of your deskop, where you will find a "start" option. You can use the "Windows +C" shortcut to pop out the charms bar Option 2: There is a hidden "start area"in  the bottom left corner of your desktop

Install nested KVM in VMware ESXi 5.1

In this blog, I will explain the steps required to run a nested KVM hypervisor on  Vmware ESXi. The installation of KVM is done on Ubuntu 13.10(64 bit). Note: It is assumed that you have already installed your Ubuntu 13.10 VM in ESXi, and hence we will not look into the Ubuntu installation part. 1) Upgrade VM Hardware version to 9. In my ESXi server, the default VM hardware version was 8. So I had to shutdown my VM and upgrade the Hardware version to 9 to get the KVM hypervisor working. You can right click the VM and select the Upgrade hardware option to do this. 2)In the ESXi host In /etc/vmware edit the 'config' file and add the following setting vhv.enable = "TRUE" 3)Edit the VM settings and go to VM settings > Options  > CPU/MMU Virtualization . Select the Intel EPT option 4) Go to Options->CPUID mask> Advanced-> Level 1, add the following CPU mask level ECX  ---- ---- ---- ---- ---- ---- --H- ---- 5) Open the vmx

Virtual fibre channel in Hyper V

Virtual fibre channel option in Hyper V allows the connection to pass through from physical  fibre channel HBA to virtual fibre channel HBA, and still have the flexibilities like live migration. Pre-requisites: VM should be running Windows Server 2008, 2008 R2 or Windows Server 2012 Supported physical HBA with N_Port Virtualization(NPIV) enabled in the HBA. This can be enabled using any management utility provided by the SAN manufacturer. If you need to enable live migration, each host should be having two physical HBAs and each HBA should have two World Wide Names(WWN). WWN is used to established connectivity to FC storage.When you perform migration, the second node can use the second WWN to connect to the storage and then the first node can release its connection. Thereby the storage connectivity is maintained during live migration Configuring virtual fibre channel is a two step process Step 1: Create a Virtual SAN in the Hyper-V host First you need to click on Virtual